Falcon, CO · El Paso County

Log & Cedar Home Staining in Falcon

The short answer

Log & Cedar Home Staining in Falcon, CO: Stripping or blasting, borate treatment, chinking inspection and a stain system built for the UV load above 7,000 feet.

What it costs: Log work is priced per building after inspection, because stripping method and chinking condition drive it far more than size does. Maintenance coats on a sound finish cost a fraction of a full strip and re-stain, which is the argument for staying ahead of the cycle rather than waiting for visible failure.
What is included: Media blasting or chemical stripping of failed finish; Borate treatment against rot and wood-boring insects before coating; Chinking and caulk joint inspection, with failed sections cut out and replaced; Log-specific stain systems, applied in the coats the system actually specifies; Clear topcoat where the system calls for it; Elevation-by-elevation assessment so the schedule matches the exposure.
Where we work: Falcon and the surrounding El Paso County, including Meridian Ranch, Woodmen Hills, Latigo Trails.
Getting a quote: Free and no obligation. Call (719) 963-7440 or request a quote online.

A log home is a maintenance commitment rather than a finish, and homeowners who move up from the Springs are frequently surprised by how much faster coatings fail at 8,000 feet. South and west elevations on a log home in Woodland Park can need attention in half the time the north side does, and treating the whole building on one schedule wastes money on one side and neglects the other.

What this means in Falcon specifically

Siding and paint substrates here

Predominantly stucco and vinyl with painted trim, on homes now old enough that original caulk joints are failing. The paint problem here is almost always trim and joints rather than the field.

Snow load and ice damming

Snow tends to blow rather than accumulate. Drifting against parapets, valleys and north-facing slopes causes uneven load and localised ice damming, while adjacent exposed sections stay bare.

Wind exposure

The most wind-exposed part of our service area. No windbreak in any direction, and sustained wind is the dominant force on these roofs. Shingle uplift at rakes and ridges is routine, and roofs here age visibly faster on the windward side.

What ends up in the gutters here

Minimal mature tree cover across the newer developments, so organic loading is genuinely light and gutter guards are frequently not worth the money here. What does accumulate is wind-driven plains grit and shingle granules, which settle into a dense sludge in the bottom of the trough. That holds water rather than blocking flow, and it is the reason a gutter can look clear from the ground and still be rotting from the inside.

Falcon sits at approximately 6,900 feet.

What is included

Media blasting or chemical stripping of failed finish
Borate treatment against rot and wood-boring insects before coating
Chinking and caulk joint inspection, with failed sections cut out and replaced
Log-specific stain systems, applied in the coats the system actually specifies
Clear topcoat where the system calls for it
Elevation-by-elevation assessment so the schedule matches the exposure

How we do it

1
Assess each elevation separately
South and west take the UV and fail first. North and east often have years left. A single answer for the whole building is nearly always wrong on a log home.
2
Strip back to sound wood
Media blasting is the usual method and it is as much about the operator as the equipment — too aggressive and you raise the grain and damage the surface, too gentle and old finish stays behind and the new coat fails over it.
3
Treat before coating
Borate treatment goes on bare wood and protects against rot and boring insects from inside the log. It has to be done before any finish, and it cannot be added later without stripping again.
4
Check the chinking
Failed chinking lets water into the log, and no stain compensates for that. This is inspected and repaired as part of the job rather than quoted as a surprise.

What it costs

Log work is priced per building after inspection, because stripping method and chinking condition drive it far more than size does. Maintenance coats on a sound finish cost a fraction of a full strip and re-stain, which is the argument for staying ahead of the cycle rather than waiting for visible failure.

We quote Falcon properties before starting, and the number you hear is the number you pay. If something on site changes the scope, you hear about it before we do the work rather than on the invoice.

Neighborhoods we serve in Falcon

Meridian Ranch, Woodmen Hills, Latigo Trails, and everywhere else in Falcon.

Fully Insured

Free Photo-Documented Inspection

Written Scope Before You Sign

Locally Owned & Operated

Log & Cedar questions from Falcon

How often does a log home need re-staining at elevation?

Commonly 3 to 5 years on south and west elevations and 5 to 8 on north and east, which is roughly half the interval you would expect at lower altitude. UV is the dominant factor and it is meaningfully more intense at 8,000 feet than at 6,000.

Is media blasting safe for the logs?

In competent hands, yes, and it is usually the best method. It is also easy to do damage with, raising the grain or eroding softwood. Ask what media they use and ask to see a test patch on an inconspicuous elevation before they do the whole building.

What is borate treatment and do I need it?

A mineral salt that penetrates the wood and makes it unpalatable to rot fungi and boring insects. On bare logs it is cheap insurance and the window for applying it is only open while the wood is stripped. If you are already paying to strip a log home, skipping it is a false economy.

Can you just recoat over the existing finish?

If the existing finish is sound, compatible and the same system, a maintenance coat is legitimate and much cheaper. That is the ideal maintenance cycle. Once a finish has actually failed, recoating over it fails with it, and the strip is unavoidable.

Related work in Falcon

Often booked together

Log & Cedar in nearby communities

All painting in Falcon →Everything we do in Falcon →